See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LTD
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Aluminum Fishing Lure Molds
The 4.6″ Freakin Frog is a top water frog bait. It’s legs kick/flop to create a small splash of water and a bubble trail as it is retrieved on a slow/moderate to fast retrieve. The body of this bait is .85″ wide and .52″ thick. The body also features a life-like profile with bumps down the […]
Aluminum Fishing Lure Molds
Epic Bait Molds 5 Inch CLASSIC STICKBAIT MOLDS – 4 and 8 Cavity
The Classic Stickbait features a worm-like rib texture and a gently tapered tail. Designed for the wacky rig, texas rig, carolina rig and other bass fishing techniques. 5″ Classic Stickbait – 4 Cavity Mold size – 3″x6.125″ 8 Cavity Mold size – 6″x6.125″ Bait size – 5″ long x 0.393″ thick More sizes coming soon, email us at EpicBaitMolds@gmail.com if you […]
Aluminum Fishing Lure Molds
This “fluke style” or “jerk bait” style bait measures 5 inches from nose to tail with a body width of .38″ and a mid body thickness of .6″. The belly features a deep hook slot to allow great hookup ratios on ewg style hooks. The back features a divot down the center for aligning and […]
Aluminum Fishing Lure Molds
The 6.2 Inch Lizard bait has a total length of 6.2 inches with the curly tail extended. The body of this bait is .35″ from back to belly and .46″ from side to side at the widest part. This bait also features curly tail arms that kick at a very slow retrieval rate along with a long […]
Aluminum Fishing Lure Molds
Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT
The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]
Aluminum Fishing Lure Molds
The 5 Inch Flappin Drax bait has a total length of 5 inches, body width of .8″ (including ribs), and body thickness of .46″ (including ribs). There are a total of 10 ribs along the body and the last two near the tail of the bait are recessed (slightly indented) to accommodate the hook point. The bait is also […]
Aluminum Fishing Lure Molds
The 6 Inch Finesse Worm is 6 inches total length with a diameter of .33″ at the thickest part of the body. The bottom of the bait is flat in overall shape but the ribbing on the body goes all the way around the worm. Mold size – 3″x7″ Number of cavities – 5 All molds are […]
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Air Clamp/Vise
Recommended air pressure 110 to 140PSI. If possible, use an air inline filter to extend the cylinder life. Always check your compressor for moisture. Keep molds centered to get the best out of this clamp. Do not leave plugged in with pressure when not in use. Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. Clean with compressed air. Do not use chemicals or abrasives. (wd40 safe for cleaning) Do not exceed 140 psi. Servicing. Add very little Tool oil once every month. (About 4 drops is all you need to lube the system.) (Do not use WD40 in the air lines.)
Plastisol Additives
High grade hardener used to get the exact hardness you prefer. Simply add this hardener to any of the plastisols offered and dial in the hardness of your custom bait and tackle. Offered in pints and quarts.
2 Litres of Plastisol
- Choose Formula
All
Thank your for your purchase from Bait Plastics. Below are some instructions and helpful tips. Lure Plastisol Formulations – Bait Plastics offers the below formulations for you exact needs. 112 Super Soft – This formula is great for drop shot and finesse baits. This is our softest formula and guarantees great action in the water. […]
Hand Injectors
Hand Injectors with screw on tip. 4 Ounce Injector = $89.99 6 Ounce Injector = $99.99 10 Ounce Injector = $119.99 12 Ounce Injector = $129.99
Aluminum Fishing Lure Molds
The 3 Inch Epic PreyBait, “hand injection” style mold was designed as part of a collaboration with Marling Baits. The Epic PreyBait is a boot tail swimbait with a rear fin designed to have an intense action with realistic presentation at any speed, with a kick and wobble on the fall. This bait/mold does not have a hook slot and is intended to […]
High Quality, High Strength TIN CURE RTV Silicone
POLYSOL's RTV silicone mold making rubber is a two-component material.
There is a Part A and a Part B that is mixed together at a 10/1 ratio
APPLICATIONS: -
|
We love the opportunity to speak with our customers and can be reached
at csr@baitplastics.co.uk
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.